Building OFW for QEMU
This page tells how to build the x86 version of Open Firmware to run under the QEMU emulator. In this version, OFW replaces QEMU's normal "bios.bin" file, so QEMU boots directly into OFW, without a conventional BIOS. This version supports most of QEMU's I/O capabilities, illustrating some of the things that OFW can do. See the #QEMU Options / Things to Try section.
The OFW tree contains a version of the platform-specific "early startup" code that is suitable for initializing QEMU's virtual hardware. The early-startup code for QEMU is as simple as such code can possibly be, because the QEMU core system "hardware" requires no initialization. On real hardware, you must turn on PLLs, configure bus bridges and superIO chips, detect DRAM characteristics and configure memory controllers, and do other complex chipset-dependent things in the early stages of startup. QEMU omits all that "magic" stuff that is outside of generic x86 programming models, so the only system-specific early startup code for QEMU is a simple memory sizing loop.
In addition to this "direct" version, there are two other ways to run OFW under QEMU:
- You can build OFW as "payload" for Coreboot, so Core boot does the early-startup stuff - see OFW as a Coreboot Payload.
- You can boot OFW from a conventional BIOS - see Building OFW to Run Under BIOS
- Open Firmware rev. >= 1051
- GCC and GNU make - OFW builds with most versions
Get QEMU >= 0.9.1 from http://bellard.org/qemu/download.html
Building Open Firmware
Get the Open Firmware source:
cd openfirmware/cpu/x86/pc/emu/build make
After make is finished (it shouldn't take long) there should be a file "emuofw.rom" in the build directory. Copy this to your qemu directory.
Run Your ROM Image
qemu -L . -bios emuofw.rom -hda fat:.
That is the basic invocation; you should get a console window with OFW running in it. OFW is using the emulated Cirrus graphics display in linear framebuffer mode, not in VGA mode.
QEMU Options / Things to Try
QEMU has lots of options that let you do all sorts of fun things. The following sections illustrate a few of OFW's I/O capabilities.
If you look in OFW's startup banner, you should see "128 MiB memory installed". That is QEMU's default memory size. You can change that by adding "-m NNN" to the qemu command line, for example:
qemu -L . -bios emuofw.rom -hda fat:. -m 32
OFW as configured will work with power-of-two size between 32 and 2048 MiB (although my QEMU installation only works up to 1024 MB). Those limits aren't inherent inheret OFW, but rather artifacts of the way this particular "port" is configured.
Hard Disk Images
The command line argument "-hda fat:." as shown above makes the current directory on the host system appear to OFW as an IDE hard disk with a read-only FAT filesystem. You can inspect it with:
ok .partitions c ok dir c:\
The device name "c" is a devalias. You can see the actual device name with:
ok devalias c ok devalias
Instead of that "virtual FAT filesystem", you can make use Linux tools to make a filesystem image. In this example, we'll create a 10 MByte image with a single partition and an ext2 filesystem:
$ dd if=/dev/zero of=filesystem.img bs=1M count=10 $ /sbin/mke2fs -F filesystem.img $ dd if=filesystem.img of=fs.img bs=512 seek=1 $ rm filesystem.img $ /sbin/sfdisk -L -uS -C 10 -H 64 -S 32 fs.img <<EOF ,,L,* ; ; ; EOF $ mkdir mnt $ sudo mount -o loop,offset=512 fs.img mnt $ # Now copy some files to "mnt" $ sudo umount mnt $ qemu -L . -bios emuofw.rom -hda fs.img
In the QEMU OFW console window:
ok dir c:\
In the recipe above, the total size (10 MiB) appears on the first "dd" line (count=10) and on the "sfdisk" line (-C 10). The sfdisk values for heads (-H 64) and sectors (-S 32) are set so that the cylinder size is 1MiB (64*32*512), making it easy to set the overall size with the cylinders (-C) argument. It is more common to use the maximum values -H 255 -S 63 in order to maximize the possible overall size, but that results in a cylinder size of just under 8M, which isn't quite as easy to work with for this example. The recipe uses two "dd" lines instead of making the image file in one step because the "mke2fs" command doesn't give you the option of skipping the first sector where the partition map has to be located.
You can tell QEMU to emulate a serial port by adding "-serial NAME" to the command line, as with:
$ qemu -L . -bios emuofw.rom -hda fat:. -serial `tty`
Then you can tell OFW to use the serial console with:
ok com1 io
QEMU has lots of options for directing the emulated serial port to various places, including real serial ports on the host system and network connections to other machines. Read the QEMU documentation (-serial option) for more information.
You can configure OFW to use the serial port by default, instead of the graphics screen and emulated PC keyboard. To do so, uncomment the line "create serial-console" in openfirmware/cpu/x86/emu/config.fth and re-execute the "make" command. Serial consoles are convenient because it's usually easy to cut-and-paste Forth code into the window that is acting as the "terminal emulator" for the serial console; you can't paste into QEMU's graphical console.
OFW has an extensive network stack, supporting many protocols including TFTP, NFS, HTTP (client and server), and Telnet (client and server). Here's an example qemu command line with networking support enabled:
$ qemu -L . -bios emuofw.rom -hda fat:. -net nic,model=pcnet -net tap
Consult the QEMU documentation (the "-net" option) to learn how to configure the "tap" interface to connect through to the real network.
Here are some OFW networking commands that you might want to try:
ok watch-net ok debug-net ok ping yahoo.com ok undebug-net ok ping firmworks.com ok more http:\\firmworks.com\hello.fth ok fload http:\\firmworks.com\hello.fth ok telnetd telnet://10.20.0.107
Now start a telnet client on some machine, connecting to the IP address shown. Quitting the telnet client restores the OFW prompt to the QEMU console.
ok telnet 10.20.0.5
Instead of "10.20.0.5", use the hostname or IP address of a telnet server. To exit, type Ctrl-] .
ok httpd http://10.20.0.107
OFW also supports IPV6 networking, but it's not compiled into this version.
You can, of course, boot operating systems over the network, using TFTP, NFS, or HTTP.
OFW uses the display in linear framebuffer mode, so it can display 2D graphics. To see a simple demo:
ok fload http:\\firmworks.com\testrect.fth
To clear the screen afterwards:
OFW has a graphical menu system that is not enabled in this configuration. You can navigate it with either the mouse or the keyboard. OFW can display .BMP files.
To make QEMU emulate a USB mass storage device, do this:
$ qemu -L . -bios emuofw.rom -hda fat:. -usbdevice disk:fat:.
Then, in OFW:
ok probe-usb ok dir u:\
"p2" is an alias for "probe-usb" for us lazy people. Since OFW tries not to do stuff "behind your back", if you plug in a new USB device, you must tell OFW to rescan the USB bus. In this case, it will have already scanned the device (it does that automatically at startup), but rescanning is a convenient way to get OFW to show you what is there. You could instead say:
ok show-devs usb
but "p2" is easier to type.
In the qemu command, you could attach a writable disk image with, for example:
$ qemu -L . -bios emuofw.rom -hda fat:. -usbdevice disk:fs.img
assuming that you have created a suitable fs.img file as per the instructions above. You can't use the same writable image for both -hda and -usbdevice, but it's okay to use the same read-only image (as with the fat:<directory> syntax) for both.
OFW has reasonably good support for a wide selection of USB mass storage devices - flash keys, disks, CDROMs, multi-card readers, etc. OFW also supports USB keyboards, but I haven't yet figured out how to make that work under QEMU. OFW supports some USB 2.0 network interfaces and some USB-to-serial adapters. You might be able to make those work using QEMU's ability to connect to real USB devices on the host. On real hardware, OFW supports UHCI (USB 1.1), OHCI (USB 1.1), and EHCI (USB 2.0) host controllers.
To enable sound support in QEMU, do this:
$ qemu -L . -bios emuofw.rom -hda fat:. -soundhw sb
ok select /sound ok d# 200 d# 2000 tone ok unselect
That plays a 200 Hz sine wave for 2 seconds (2000 mS). OFW can also play .wav files, but that's not included in this configuration.
QEMU has a lot of options to control the sound emulation; read the documentation to get totally confused.
OFW's SoundBlaster driver, as included in this configuration, is rather rudimentary. OFW has better drivers for the more common AC97 sound hardware.